Frequently loosing connection to X-Plane
BRUNNER Forum › Forums › Software › CLS2SIM Software › Frequently loosing connection to X-Plane
This topic contains 10 replies, has 4 voices, and was last updated by johnrutoski 1 month ago.
-
AuthorPosts
-
12. September 2020 at 11:43 #2015
Hey,
Version: http://files.homepagemodules.de/b167881/f49t484p1918n43_kdaEGNOe.png
X-Plane 11.41 and 11.50, Win10, CLS-E NGI am frequently loosing connection (and therefore any control) with X-Plane.
– every time when changing the aircraft (I can live with that)
– still much too often during flight (that´s nasty)
– very often during helicopter flightNow for possible reasons. Meanwhile I set up a little window into my videos to see the “LED” if CLS2sim is still connected to the sim (half way up on the right side). In this video it lost connection when I changed the time of day. Coincident?
Video:
…and a reconnect disconnects the autopilot: https://youtu.be/SvSJcy1XXws?t=1247
…again when fiddeling in the menu: https://youtu.be/SvSJcy1XXws?t=2055
A timeout problem?
Again when being in menu: https://youtu.be/DutXxwPeTYw?t=1121
Reconnect stops main rotor (with unhappy ending but most likely not a Brunner problem) https://youtu.be/DutXxwPeTYw?t=1464
Replay outside view: https://youtu.be/DutXxwPeTYw?t=1668Second problem: when changing the active window by Alt-Tab I always have to select the CLS2sim window twice. Since I normally do that only because it has lost the connection to the sim one might have something to do with the other.
Any idea where to start looking for the problem?
14. September 2020 at 10:26 #2022Hi langschwert
It is normal that you loose connection when you are in the menue in X-Plane 11
Just enable Auto Connect under Simulator in Connection Settings
see also here…
https://cls2sim.brunner-innovation.swiss/SettingsForm.htmRegards
Stefan Brunner14. September 2020 at 11:53 #2024I just delightfully wanted to try that – but it already is set that way and still loses connection and doesn´t reconnect automatically. It only automatically connects to the yoke (not being the problem anyway) but not to the sim.
http://files.homepagemodules.de/b167881/f49t484p1918n45_YpPovrGf.pngIs there anything wrong with my settings?
14. September 2020 at 12:08 #202514. September 2020 at 12:32 #2027Aaaagrh! “Blinded by the light…” *sing* https://www.youtube.com/watch?v=lcWVL4B-4pI
Tried and works. Thank you so much! 🙂
15. November 2020 at 10:58 #2139Hello,
I also have this problem.
It does not only occur in pause mode or when I am in a menu of X-Plane, but also when reloading the scenery takes a bit longer (2-3s).
If this happens, like when approaching EDDS westwards, the 10 seconds it takes autoconnect to reconnect means a crash.Is it possible to extend the time until a disconnection or shorten the time for a new connection?
I have looked at all the findable config files, I could not find a corresponding parameter so far.The way it works (not) with X-Plane now, an approach with photorealistic scenery is a dice game.
Greetings
Günther15. November 2020 at 11:02 #2140I forgott,
the interruptions are much more frequent since I am using version 11.50 of X-Plane (I use the Vulkan driver).20. November 2020 at 10:56 #2151Hello,
I also have this problem.
It does not only occur in pause mode or when I am in a menu of X-Plane, but also when reloading the scenery takes a bit longer (2-3s).
If this happens, like when approaching EDDS westwards, the 10 seconds it takes autoconnect to reconnect means a crash.Is it possible to extend the time until a disconnection or shorten the time for a new connection?
I have looked at all the findable config files, I could not find a corresponding parameter so far.The way it works (not) with X-Plane now, an approach with photorealistic scenery is a dice game.
I know you are busy, so a yes or no would be enough (for the first time) 🙂
Regards
Günther11. December 2020 at 13:10 #2182Hello again,
Here is an example of how the long duration of reconnection affects.
The video shows the disconnection a few seconds after the video start, when the connection was given again can be clearly seen.It looks like CLS2SIM does not use a stable method for the connection to X-Plane.
It would be helpful if there were no 10 seconds delay for the reconnection to start.I find it strange that I do not get an answer from Brunner.
I guess the only thing left for me to do is to open a ticket./Günther
11. January 2021 at 14:47 #2246Still no answer.
Maybe too much work with new MSFS 2020 customers, time to forget older ones, huh?7. March 2021 at 22:06 #2371I have the same problem in Xplane 11.52R2 and CLS version 4.29 when pausing or changing location the controls takes more than 10 seconds to reconnect. It ends up causing a crash when I move aircraft at low altitude. This occurred all along but the reconnect time was much less with older versions of the CLS software.
-
AuthorPosts
You must be logged in to reply to this topic.