X-Plane not remembering calibration of yoke

BRUNNER Forum Forums Products CLSE-Yoke X-Plane not remembering calibration of yoke

This topic contains 8 replies, has 4 voices, and was last updated by  rickcn 1 day, 12 hours ago.

Viewing 9 posts - 1 through 9 (of 9 total)
  • Author
    Posts
  • #1824

    geronimopilot
    Participant

    Hello all.

    This is my first purchase of a Brunner product. So far I am impressed with the unit.

    Upon installation, X-Plane asked me to calibrate the yoke so I did. Now, every time I launch X-Plane it asks me again. This cannot be right! Am I doing something wrong? Please help.

    Scott

    #1825

    maximb
    Participant

    Hi and congrats for your purchase !

    First, you need to use CLS2Sim software and you don’t need to calibrate the yoke in Xplane. You have to install the Vjoy driver which is a Virtual Joystick for xplane and which will communicates between Xplane and CLS2Sim. To avoid problem in Xplane, just set 1 axis for the pitch, and 1 for the Roll for the Vjoy and that’s it ! You can also map buttons of your yoke directly in Xplane, but not the Axis ๐Ÿ˜‰

    Good Flights ๐Ÿ™‚

    #1826

    jovabra
    Participant

    Hi, i’m the happy owner (more than 3.5 year) of the Brunner yoke
    First you must install the CLS2sim software. After installation you find the Brunner map on your C-drive if you using the basic settings.
    For example: C>Program Files (x86)> Brunner Electronik AD> CLS2sim> Simulator plugin installers. For X-plane you find the x-plane installer so
    run this with admin rights.
    This plugin software is the interface between the yoke and X-Plane. vJoy is not necessary for the yoke. I only use vjoy to assign the buttons on the yoke.
    For example stab trim etc. The Brunner interface software bypassed the X-Plane settings for the Aileron/Elevator.
    Succes
    John

    #1827

    geronimopilot
    Participant

    Thanks maximb/jovabra,

    Can you tell me where to find Vjoy?

    Best,
    Scott

    #1828

    jovabra
    Participant

    vJoy software is in the BprogramFiles (86) >Brunner Electronic AD> CLS2sim > Vitual joystick driver
    We can’t make it any easier
    Regards
    John

    #1829

    maximb
    Participant

    Jovabra, you don’t have Vjoy in your xplane list of hardware?

    I have it and I have to assign Pitch and Roll to a virtual axis of the Vjoy because if not I have a cross in the center of the screen when I’m flying.

    But if you tell me you do differently.. i can try your solution ๐Ÿ™‚

    #1830

    jovabra
    Participant

    If you have a crosshair in your flightsim this is a wellknown X-Plane item. In this case you have mouse controle i.s.o the Brunner yoke.
    Google is your friend. Search for crosshair in X-Plane.
    Some information about the CLS2sim installation.

    vJoy is active in my X_plane hardware setup but only for some buttons.
    Advice: if you do some modifications in the X-Plane settings you must reconnect the CLS2sim.
    Success

    #1831

    maximb
    Participant

    Thanks Jovabra. This is exactly the way I installed the plugin.

    In Xplane Hardware Setup, I have no axis assigned for the Yoke, but Pitch and Roll and assigned in the vJoy to avoid the Crosshair.

    I understand that you don’t use this method… You assigned Pitch and Roll directly on your Yoke (in Xplane)? And CLS2SIm bypass this assignment ?

    #1848

    rickcn
    Participant

    Hi guys,

    I really need some help. I donโ€™t understand why xplane states I did not properly connect/calibrate the Brunner joystick and asks me to recalibrate every time I start a flight..

    So canโ€™t we use the Brunner joystick, and if so, can we disable it in xplane11? Secondly, how to configure vjoy with 12 axis? Ignore them all? Where are the buttons defined as I only see two who are active in the interface…

    Is there a detailed step by step instruction manual?

    Rick

Viewing 9 posts - 1 through 9 (of 9 total)

You must be logged in to reply to this topic.

BRUNNER ELEKTRONIK AG

Industriestrasse 27
CH-8335 Hittnau

tel +41 (0)44 953 1010
fax +41 (0)44 953 1019

info(at)brunner-innovation.swiss

Help-Desk